H3 License plate relocation

[ConcealedGLOCK]

Want to move my license plate to my spare tire so I can mount a reverse camera with it. What mount system did you guys go with? I'm not needing it to have a brake light just as long as it comes with wiring harness for the white light.

 

[rascole]

Why not put the camera in the bumper above the hitch receiver? 3/4" hole is all you need.

 

[4speedfunk]

Here’s the one I’ve had for several years...
https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/401607210351

 

[ConcealedGLOCK]

Why not put the camera in the bumper above the hitch receiver? 3/4" hole is all you need.

Because I'm wanting to relocate the plates for a cleaner look. The camera being there is just a plus. I've already had it down there and due to where my exhaust is, it melted my wires. Which on my fault looked like it was far away enough.

 

[ConcealedGLOCK]

Here’s the one I’ve had for several years...
https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/401607210351

Thank you. So far it looks like this might be the one I go with unless others got a great option without brake light option.

 

[PbSlinger]

Switched to this one after putting my Thorparts bumper on. Works pretty good. Added motorcycle license plate lights which take the place of the top plate bolts.

https://www.amazon.com/gp/product/B07JJ2NWDT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

 

[scoreh3]

Switched to this one after putting my Thorparts bumper on. Works pretty good. Added motorcycle license plate lights which take the place of the top plate bolts.

https://www.amazon.com/gp/product/B07JJ2NWDT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

i haven’t seen that one before. I like it better than the normal Jeep one. The camera below is a nice setup. That just might be a new project.
Thanks

 

[ConcealedGLOCK]

Switched to this one after putting my Thorparts bumper on. Works pretty good. Added motorcycle license plate lights which take the place of the top plate bolts.

https://www.amazon.com/gp/product/B07JJ2NWDT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

That's a good option. Also does it actually come with that rear view camera? Not seeing it mentioned in their description.

 

[cbetts]

I used the Tuff Stuff model from Amazon: :link:

 

[bigwilliedw01]

Warrior Products 2370 Spare Tire License Plate Mount https://www.amazon.com/dp/B008HTBZIM/ref=cm_sw_r_cp_apa_i_zUd5CbQZH9XFY

This is what I have. A little pricey, but it has a quick release so it doesn't need to be unbolted to remove spare. I made a quick connect harness that runs thru it for plate lights, camera, or whatever else you want to run.

Sent from my SM-J730F using Tapatalk

 

[PbSlinger]

That's a good option. Also does it actually come with that rear view camera? Not seeing it mentioned in their description.

No camera option. But could relocate it. It does take a couple of screws to get to the spare, but...$39.00

 

[jakesz28]

I am using the same bracket 4speed posted. Been on 5+ years and I have never had a license plate light this whole time. Never even been stopped for it.

 

[ConcealedGLOCK]

I am using the same bracket 4speed posted. Been on 5+ years and I have never had a license plate light this whole time. Never even been stopped for it.

Not going to lie I'm liking that quick disconnect. Also with the cheaper $32 mount the motorcycle bulbs would be a lot more work if the bulbs go out. How's the bulb on that rock hard mount? Is it a fixed into the housing or can it be popped out to be replaced?

 

[jakesz28]

Not going to lie I'm liking that quick disconnect. Also with the cheaper $32 mount the motorcycle bulbs would be a lot more work if the bulbs go out. How's the bulb on that rock hard mount? Is it a fixed into the housing or can it be popped out to be replaced?

I have the plate mount, but no light. Never had a plate light in over 6 years.

 

[ConcealedGLOCK]

Switched to this one after putting my Thorparts bumper on. Works pretty good. Added motorcycle license plate lights which take the place of the top plate bolts.

https://www.amazon.com/gp/product/B07JJ2NWDT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Did you modify the mount? Looks like the only way it will fit is at a slightly crooked.

 

[PbSlinger]

Ok. After a couple months of use, the mount I posted from Amazon and used, is totally trashed. The "lugs" that are used to secure it are not the right size and stripped, then the mounting screws that go into the "lugs" are also no good.
Can't recommend. Back to the drawing board for me.

 

[ConcealedGLOCK]

For people looking into this. I'd stay away from thus option posted here. Not sure what bolt pattern was used but didn't work for me. (Good thing I got a jeep too)

Switched to this one after putting my Thorparts bumper on. Works pretty good. Added motorcycle license plate lights which take the place of the top plate bolts.

https://www.amazon.com/gp/product/B07JJ2NWDT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Instead buy this one. Went with this after and it works great.

Here’s the one I’ve had for several years...
https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/401607210351